各位大大們好...小弟是Delihpi的初學者.. 請問大大們....小弟看不懂這些步驟...有人可以教我嗎? 謝謝 小弟從第三步驟就開始不明白了 >"< 不好意思 英文沒學好 To install TurboPower LockBox into your IDE, take the following steps: 1. Unzip the release files into a directory (e.g., d:\lockbox). 2. Start Delphi or C Builder. 3. Add the source subdirectory (e.g., d:\lockbox\source) to the IDE's library path. 4. Open & install the designtime package specific to the IDE being used. The IDE should notify you the components have been installed. a. For C Builder 6 and Delphi 6 or higher, install the VCL design-time package (e.g., LxxxVDxx.*) when using LockBox classes with VCL applications. b. For C Builder 6 and Delphi 6 or higher, install the CLX design-time package (e.g., LxxxCDxx.*) when using LockBox classes with CLX applications. 5. Make sure the PATH environmental variable contains the directory in which the compiled packages (i.e., BPL or DPL files) were placed.

引言: 各位大大們好...小弟是Delihpi的初學者.. 請問大大們....小弟看不懂這些步驟...有人可以教我嗎? 謝謝 小弟從第三步驟就開始不明白了 >"< 不好意思 英文沒學好 To install TurboPower LockBox into your IDE, take the following steps: 1. Unzip the release files into a directory (e.g., d:\lockbox). 解壓這些檔案到一個檔案夾, 如 d:\lockbox 2. Start Delphi or C Builder. 啟動 Delphi, 或 C Builder 3. Add the source subdirectory (e.g., d:\lockbox\source) to the IDE's library path. 將第1項的source路徑加入到Delphi中的 IDE Library 路徑中(在 Tools->Environment Options -> Library) 4. Open & install the designtime package specific to the IDE being used. The IDE should notify you the components have been installed. 把屬於設計階段(Designtime)的package加入到componment中 a. For C Builder 6 and Delphi 6 or higher, install the VCL design-time package (e.g., LxxxVDxx.*) when using LockBox classes with VCL applications. a.對於 C Builder6及Delphi 6或更高的版本, 你必須加入 LxxVDxx.* 類的package到 VCL中 b. For C Builder 6 and Delphi 6 or higher, install the CLX design-time package (e.g., LxxxCDxx.*) when using LockBox classes with CLX applications. b.對於 C Builder6及Delphi 6或更高的版本, 你必須加入 LxxxCDxx.*類的Package 到 CLX(所謂Clx 是 for Kylix) 5. Make sure the PATH environmental variable contains the directory in which the compiled packages (i.e., BPL or DPL files) were placed. 確認所有的上述package的路徑(path)都確實被連結到編譯的package

大致是如此啦, 以上是英文教學~~~~, 真的要多加學習哦!

請問我一直有以下錯誤出現?? 有可能哪裡出錯?? 我用C Builder 5.0 C Error] RSAKeys1.h(9): E2209 Unable to open include file 'LbAsym.hpp' [C Error] RSAKeys1.h(10): E2209 Unable to open include file 'LbCipher.hpp' [C Error] RSAKeys1.h(11): E2209 Unable to open include file 'LbClass.hpp' .....